https://www.youtube.com/watch?v=Avp8MurmeEY

  

  ESC - Engine Speed Controler

  PDB - Power Distribution Board

  

Propellor screw depends on rotation Res engine / Black Engine


XT60 - Battery connector (2 round pins)



Racerstar RS20Ax4 20A 4 in 1 Blheli_S Opto ESC 2-4S Support Dshot150 Dshot300 for FPV Racer


On Banggood            22 Euro




F3 Flight Controller Acro 6 DOF/Deluxe 10 DOF for Multirotor Racing  21 - 29 Euro



4X Racerstar Racing Edition 2205 BR2205 2300KV 2-4S Brushless Motor 2 CW & 2 CCW For QAV250 ZMR250


26 Euro

Matek Systems PDB-XT60 W/ BEC 5V & 12V 2oz Copper For RC Multirotors 6 Euro



Eachine VTX03 Super Mini 5.8G 72CH 0/25mW/50mw/200mW Switchable FPV Transmitter Euro 11


Frame Kit   13 Euro




GPS Module





https://www.rchelicoptershop.nl


https://oscarliang.com/best-flight-controller-quad-hex-copter/



over drone motors:

http://www.dronetrest.com/t/brushless-motors-how-they-work-and-what-the-numbers-mean/564




Jasper van Loenen:


https://jaspervanloenen.com



Karel Doormanhof (straat in video)

Turnigy Radio Remote coltroller.


http://www.instructables.com/id/DIY-Drone-It-Yourself-Kit-v10/



ESC:

https://hobbyking.com/en_us/turnigy-plush-30amp-speed-controller.html



Turnigy ???? mekr door HobbyKing






==================================================================

   3D PRINTS

==================================================================

Print the following parts (preferably in ABS, I haven't tried them in PLA):


4 x motor_mount.stl

4 x clamp.stl

4 x clamp_bar.stl

4 x bolt_handle.stl

1 x box_top.stl

1 x box_bottom.stl


(Optional) If you need some extra range, also print:

4 x extender.stl


==================================================================

   SCREWS / NUTS / BOLTS

==================================================================


To put everything together, you will need some nuts, bolts and washers. You can source them yourself, or use the below mentioned item numbers on rs-online.com:


189-620 - Plain washer, M3 - four for each motor

293-325 - Hex socket cap screw, M3x20mm - four for each motor

521-850 - Wing nut, M4 - one for each clamp (two with extender)

189-636 - Plain washer, M4 - two for each clamp (four with extender)

290-118 - Hex socket cap screw, M4x30mm - one for each clamp (two with extender)

279-571 - Hex bolt, M4x60mm - one for each clamp


==================================================================

   ELECTRONICS

==================================================================


4 x Motor

1 x Propeller kit (2 times left and 2 times right rotating)

1 x Propeller accessory pack

4 x ESC (electronic speed controller)

1 x transmitter + receiver (with a minimum of four channels)

1 x LIPO battery

1 x Battery charger


Apart from these parts you will need a flight controller. I've been using the opensource OpenPilot CC3D. More info on the OpenPilot project can be found on openpilot.org (and especially in the forums).


For the other components, below you will find a list of the ones I've been using. For the kit, I've tried to keep costs down and used parts that are easy to order online.


Motor:

NTM Prop Drive Series 28-26A 1200kv / 250w

http://www.hobbyking.com/hobbyking/store/__17345__NTM_Prop_Drive_Series_28_26A_1200kv_250w.html


Propellers:

10x4.5 SF Props 2pc Standard Rotation/2 pc RH Rotation (Black)

http://www.hobbyking.com/hobbyking/store/__25824__10x4_5_SF_Props_2pc_Standard_Rotation_2_pc_RH_Rotation_Black_.html


Prop accessory pack:

NTM Prop Drive 28 Series Accessory Pack

http://www.hobbyking.com/hobbyking/store/__16719__NTM_Prop_Drive_28_Series_Accessory_Pack.html


ESC:

TURNIGY Plush 30amp Speed Controller

http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=2164


Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)

http://www.hobbyking.com/hobbyking/store/__8992__Turnigy_9X_9Ch_Transmitter_w_Module_8ch_Receiver_Mode_2_v2_Firmware_.html


Turnigy nano-tech 3000mah 3S 25~50C Lipo Pack

http://www.hobbyking.com/hobbyking/store/__11919__Turnigy_nano_tech_3000mah_3S_25_50C_Lipo_Pack.html


Turnigy Accucel-8 150W 7A Balancer/Charger

http://www.hobbyking.com/hobbyking/store/__7523__Turnigy_Accucel_8_150W_7A_Balancer_Charger.html




   

Created with the Personal Edition of HelpNDoc: Free help authoring tool